Industrial, Process and Environmental piping system pre-engineered and pre-fabricated to prevent primary pipe lines from leaking into the ground, onto the floor or into the air.  These engineered systems ensure a high quality piping system that will meet your stringent requirements as well as building, EPA and other government regulations.  These systems Primary and Secondary pipes can be designed with almost any type of pipe combinations, from exotic alloys to your everyday pipe materials such as carbon steel, fiberglass, copper, etc.

TYPICAL APPLICATIONS:

  • Process piping
  • Fuel Oil
  • Jet Fuel
  • Gasoline
  • Hazardous fluids

SYSTEMS:


ULTRA-HT™ is an advanced preinsulated secondary containment piping system for general fluid transportation that requires an insulated steel containment. No need for cathodic protection.


ULTRA-HT™ is the designed for maintaining fluid temperature while containing hazardous fluids. This system complies with Federal regulations for secondary containment of hazardous fluids, that require insulation to maintain their temperature. Drainable, dryable and testable, prefabricated this secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, bio-process waste and chemical transfer. ULTRA-HT™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding .100 mils thick and designed to withstand a 35,000 volt holiday test. ULTRA-HT™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.

Temp Range: 32ºF to 750ºF
Max Pressure: Determined by the carrier pipe selected
Pipe Sizes: Nom. Diameter ½” – 44″, Nom. Length 20′ and 40′

Powered by Hackadelic Sliding Notes 1.6.5


GALVA-GARD®, “The Ultimate Corrosion Fighter” is a prefabricated, preinsulated, fiberglass clad galvanized steel conduit system for low to high pressure steam, HTHW and general fluid transportation.



GALVA-GARD® the original “corrosion fighter” just got better. As always, galvanization is applied to the exterior, as well as the interior of the outer pipe providing a clean, corrosion resistant system for underground heat distribution. Now PERMA-PIPE® has added a thick cladding of fiberglass reinforced plastic on top of the galvanized system for maximum resistance to adverse corrosion and environmental conditions. There is no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick and designed to withstand a 35,000 volt holiday test. GALVA-GARD® is a smooth wall, hot dipped galvanized, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Energy Loss Detection and Location system and electric heat tracing.

Temp Range: 250°F to 750°F (standard), above 750°F (special)
Max Pressure: Determined by the carrier pipe selected
Pipe Sizes: Nom. Diameter ½” – 44″, Nom. Length 20′ and 40′

Powered by Hackadelic Sliding Notes 1.6.5


DOUBLE-PIPE™Type-HT is an economical choice for a prefabricated, preinsulated secondary containment piping system for high temperature or general fluid transportation. The system is carbon steel inside a carbon steel coated containment.

DOUBLE-PIPE™Type-HT is an economical choice for a prefabricated,  preinsulated secondary containment piping system for general fluid transportation. The system is carbon steel or stainless inside a  carbon steel coated containment. It is designed for high temperature waste lines in refineries and chemical process  sewers. This system complies with Federal regulations for secondary containment of hazardous fluids and “NESHAP” petroleum refinery compliance. This drainable , dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of jet fuel, fuel oil, diesel, gasoline, high temperature process waste and chemical transfer. DOUBLE-PIPE™Type-HT can be used  for above and below grade systems. The outer containment can be coated with urethane for Below grade applications or red mil primer suitable for  final painting on above grade systems. Single or multiple steel carrier pipes can be supplied with  any type of pipe insulation, we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PERMALERT™ Leak Detection and Location system and electric heat tracing.

Powered by Hackadelic Sliding Notes 1.6.5